SMF & MACHINE TOOLS,
INC.
14824 Rockbridge Rd Little Rock, AR 72206 fax 501-897-4090
800-643-5839 Rusty Scott
Home Page |
Used Equipment |
New Equipment |
Media |
Compounds |
Email Us
1 New Vibe Tech Model VTG-5024D Heated Cob Dryer, specified and described below.
CAPACITY5 - 7 cubic feet working capacity (depending on media)
CONSTRUCTION -3/16" Outer Wall, 1/4" Center Wall, 1/2" Top and Bottom Bearing Mounting Plate
BOWL WIDTH -52"
MACHINE HEIGHT -42"
PROCESS CHANNEL WIDTH -13"
UNLOAD HEIGHT -34"
HORIZONTAL PROFILE -1/3 Rise
MOTOR -5 HP 230/460 Volt, 3 Phase, 60 Cycle
BEARING TYPE -2 Double Row Spherical Bearings with extra clearance for vibe application
BEARING ASSEMBLY -Cast Steel, piloted housing, flange bearing
LUBRICATION TYPE -Manual Grease
PARTS LOAD CHUTE -Included
SEPARATION TYPE -Fixed ramp standard (For one pass only)
SCREEN DECK TYPE -Coated or uncoated woven wire, machined UHMW or cast polyurethane
SCREEN DECK DESIGN -Internal semi-extended screen (120 degree)
ELECTRICAL CONTROLS -NEMA control panel, 230/460/3/60, 115 volt control circuit. Panel has fused disconnect, overload protection, push button controls and total hour meter. Control panel is mounted on a fabricated frame to stand alone by the machine. Allen Bradley components are used in the panel.
HEAT SYSTEM -The tub weldment is wrapped with a 600 degree heat resistant insulation then covered with a 14 ga outer skin. Six 1000 watt heater elements are mounted on the base with three of the elements on all the time the heat system is on. The second set of three elements cycle on and off as programmed. This is set by the operator and controlled by timed relays in the control panel. The system also has a cool down timer to protect the cob meal from scorching.
ECCENTRIC WEIGHTS -Slip on style weight segments and a moveable top master weight allow for easy adjustment.
PAINT -Mill Ivory (Off White) Industrial grade enamel
FLOOR SPACE -5' x 5'
WEIGHT -Approx 1,800 lbs.
PRICE POR
OPTIONS
Manual Gate allows for batch capabilities
Dust Cover
Dust Collector (must be combined with cover) On dryer applications a 6" hole in the center of the cover is connected to the dust collector. This dust collector would be tied into the control panel and operated from the face of the panel. The dust collector is a bag design with 30 super strength dust bags, 1/2 HP motor 3 phase 400 cfm (@8"sp) and manual cleaning with shaker.
Auto Grease System is tied into the panel and will supply both top and bottom bearings with a factory set amount of grease.
DELIVERY: Call for current lead time
F.O.B: Michigan
TERMS: 50% deposit with order,balance due before ship
WARRANTY CLM Vibe Tech Inc. will warranty the above equipment against defects in workmanship and materials for a period of one year. Defective parts are to be either repaired or replaced at Seller's discretion.
FACTS & CONDITIONS The above shipping date is an approximation. Also the weight is approximate due to the options the exact may vary. Seller assumes no responsibility for faulty installation, misuse of machinery and faulty advice of others not employed by the seller. Buyer is responsible for all costs of installation and use of machinery. Seller is not responsible for any federal, state or local regulations that apply to the customer nor cost of any damage the process might cause such as inhalation of chemicals, waste, noise damage or harm from improper use.
SMF & Machine Tools, Inc. has been selling new vibratory finishing equipment since 1969. We have sold over 500 vibratory finishing machines and have set up over 1000 processes. If you have any questions about vibratory finishing, please don't hesitate to give us a call.
Sincerely,
Rusty Scott, Vibratory Sales
SMF & Machine Tools, Inc.
Return to New Vibratory Finishers Page